Need help identifying your belt? - 123roulement

Need help or advice choosing your belt?

We give you a few tips

There are many belt variants, even on a similar type. Here's a step-by-step guide to help you identify the belt you want to replace. To begin with, make sure you know where to find the belt reference number. Even if the belt is old and damaged, there are often a few letters or numbers that will simplify your search. This reference can be found on the flat surfaces of your belt, or on the belt packaging if you bought it separately. If you have the reference number of your belt, enter it here. If no reference number is visible, keep your original belt handy - it will come in handy one last time - and follow the guide!

EXPERT ADVICE

All the answers to your questions are here

How to identify your belt?

Belts

You no longer have a reference on your belt, as it's often in too poor a condition to read anything on it? Arm yourself with a tape measure, a caliper and the remains of your original belt, and answer the following questions as best you can, one after the other, to find your belt! The first question is to identify the range of your belt; the following steps require you to have the original belt. If you no longer have this belt, call your Bearingers on 0359360490, who will guide you efficiently in your search.

Useful tools before you start

In order to find the right belt for you, we recommend you use one of the following tools:

Vernier caliper
One meter
A rule
Your belt

Do you know your belt part number?

No Yes

Find your belt by part number

Please enter the reference below

Ouch, no results match your reference

results match your search

Have you found an inscription on your belt? Good news, most of the work is done! In general, you'll be able to read the belt reference, often in the form of a few letters followed by numbers. This should be enough to accurately identify the belt in the search bar opposite. Useful information: your belt is often marked with the length, but which one? Le or La = outer length Lp, Ld or Lw = pitch length Li = inner length

We suggest this 4-step questionnaire to help you refine your search.

Which range does your belt belong to?

A V-belt (smooth or toothed) is mounted on a smooth pulley, without teeth. It will be held in place and perform well thanks to its tension on the pulleys. A toothed belt has teeth, which match the teeth of the pulley. For the other variants, the images and photos we offer will help you easily identify yours.

What type of belt do you use?

You search, we find!

We invite you to contact one of our bearingers

By mail

By phone

+1(646) 712 9672

By messenger

Link

picto_need_help

Our Bearingers are at your service

Monday to Friday

8 a.m. - 7 p.m

Identify the cross-section of your belt?

Measure your belt?

Measuring the length of your belt is the most delicate part of its identification. Your old belt is often damaged, slack or even cut! Here's the best way to find out the length of your belt: - The belt is still complete: draw a chalk line on the inside of the belt, then measure from the line along the inside of the belt until you come back to the line. This will give you a good estimate of the inside length of your belt! You can do the same on the outside of your belt, to get a second measurement. Two opinions are better than one! You can also use a special tool, called a MESLA ruler, to measure your belt. - The belt is cut, sectioned: A cut belt is not easy to measure, so you'll need to use a tape measure to take the most accurate length possible, which will correspond roughly to the original length of the same new belt.
You can also use the method below for non-existent belts to estimate the length of your belt for a second time. No method is perfect for identifying a belt by its dimensions, so there is always a risk of error.* *123Roulement cannot be held responsible for any error in measurement or identification. - The belt is disintegrated, non-existent or lost: The situation is not the easiest, but there are solutions! With your pulleys in place and a long piece of string, we advise you to estimate the length of belt required: Place the string on the pulleys, taut, and measure the length it represents. This is a rough estimate of the inner length of the belt.